How To Make a "Come and Take It" Flag

In response to the protests over SB5, SB1 and HB2—and with inspiration from the amazing uterus design conceived by Carrie Collier-Brown and created by Cole Latimer—I decided I wanted to make a reusable and durable flag instead of a paper protest sign to carry in marches and to wave at rallies. It took me a few hours to get to the final product in part because I was sitting in line on the hard granite floor of the Texas State Capitol, waiting to get into the Senate Gallery.

Project Description

This is a two-sided flag design with the emblem sewn on and the letters ironed on. I made this all by hand without a sewing machine. It is intended to be used with a pole as a flag but you can certainly make adjustments as you see fit, especially those of you with more skills than me! Please leave suggestions in the comments.

Estimated time: 5 hours
Total cost: $15

Flag on the floor of the Texas State Capitol

Supplied Needed For this Project

• Black cloth for the flag, 1/2 yard of 54" fabric
  (This is enough for two flags at 27" wide and 18" tall. I used 100% polyester as most flags are made of nylon.)
• White cloth for the emblem that when  folded in half is at least 8.5" by 11"
  (Again, I used polyester—a faux suede—and used the "wrong" side of the fabric for the look I wanted.)
• Iron-on 3/4" letters in white
  (I used Dritz soft flock – CO075HWT.)
• Black thread
• Invisible thread
  (I used Wrights 882131 Clear Invisible Thread, 500-Yard.)
• Fray stop glue
  (I used Dritz 674 Fray Check Liquid Seam Sealant.)
• Scissors
• Tape measure
• Needle
• Pins
• Paper and printer for the pattern
• Masking tape
• Iron
• Pole
  (I used an old broom handle I rescued from the dumpster.)

Instructions

These are the steps I took to complete this project. Please modify to fit your own project. :)

Step 1

I started by creating my pattern based on the awesome uterus image I saw on Twitter. Download the "Come and Take It" pattern and print it on a regular sheet of 8.5" x 11" paper. After printing, cut it out carefully along the outside of the lines, not directly on them. You do not need to cut out the letters individually; we will use them as a block to line up the iron-on letters.

"Come and Take It" pattern

Step 2

Fold the white fabric in half and pin the uterus and star to it, making sure you pin it to both layers of fabric. Alternatively, you can do this twice and cut out two sets but I cut out both at once being careful to keep the fabric and pattern aligned. Don't skimp on the pins! Pin it down securely.

Pin the pattern securely

Step 3

Lay out the black fabric. If you bought 1/2 yard (18") of 54" fabric, all you need to do is cut it in half. If you have a different size fabric, use a measuring tape to mark off a rectangle 27" x 18". I'll be honest; I wasn't real worried about cutting perfectly straight lines. If you plan to hem your project, allow extra fabric for that.

Cut the base of the flag

Step 4

It's time to apply the fray stop glue. The one I bought had a nice, two sided applicator that allowed me to slip the fabric into the nozzle and squeeze to apply the glue around the edge of all my pieces: star, uterus and flag base. The glue can be a bit messy so I used cardboard scraps under the edges to keep it off my table. Smooth down any loose, frayed fabric while it's still damp then let the glue dry for a few minutes.

Apply glue to all fabric edges

Step 5

Next, let's create the pocket for the flag pole. If you don't plan to use a flag pole, move on to the next step. First, fold over and pin one of the short sides of the flag about 1/4" being sure to pin from underneath; this will be important shortly. Next, lay your flag pole on your fabric and fold over the edge you just pinned to get an idea of how large you need to make the pocket. The pole I used was about 1.5" in circumference. With the pole in place and the fabric folded over it, remove the top pin and re-pin in place, going through all three layers of fabric. Then do this for the bottom pin. Continue this until you have re-pinned everything through the three layers of fabric. Once this is done, carefully remove the flag pole.

Pin the pocket and sew shut

Using a simple looping stitch and black thread, sew the the pocket in place, including along the top of the flag to keep the pole in place. The flag base is now complete.

Step 6

On one side of the flag, lay out one star, one uterus and the block of letters from the pattern. Measure to get it centered horizontally and vertically. Once it is in place, carefully pin the star and uterus to the flag base; this can take a little adjusting, particularly with the uterus, to get it lined up correctly. Using the invisible thread and a simple looping stitch, sew the star and the uterus to the flag base. Be as careful or quick as you like. I wanted my flag to have a hap-hazard look to it.

Sew the star and uterus to the flag base

Once the first side of the flag is sewn, flip it over and you can use the stitching to line up the second star and uterus in place. Pin them down and sew to the flag base with the invisible thread.

Step 7

Start cutting out the letters in "Come and Take It". Chances are, you will not have enough letters from one pack. I ended up having to fashion an extra "E", "T" and "A" out of other letters that looked similar. Cut close to the edge of the letters leaving 1/8" of paper. Next, rip off a short piece of masking tape and begin to apply the letters in "Come" to it, paper side down, so that the letters are facing you. The letters need to be backwards, so you must apply the letters to the tape in reverse order and orientation. You can hold the tape up to the light to check if the letters look correct. Do this for each of the four words, keeping the letters close together. You can use the words from the pattern to help. Tape the four words together leaving about 1/4" between them.

Make sure to line up the letters in reverse on the tape

Step 8

Do each side of the flag separately. Take one set of letters and tape them in place, centered, under the uterus. Make sure they are straight before ironing. Set your iron to whatever setting your letter pack indicates. Pressing for no more than 15 seconds at a time, use your iron to affix the letters to the flag. I had to iron my letters several times, checking in between to see if they were sticking.

Tape all the words together in place under the uterus and iron on

Once you've ironed on the first set of letters, let it cool then remove the tape and paper. Check to make sure each letter is affixed securely; if not, re-iron those letters. Next, do the same thing to the other side of the flag.

Step 9

Tada! You now have a bad ass flag. Insert the flag pole or just hold your flag and go protest to your heart's content.

Protesting HB2 at the Texas State Capitol